Skip to main content

The Total Protection Roofing System, part by part

The parts of the Owens Corning Total Protection Roofing System, what each one does, and why mixing in any other part can affect the roof and its warranty.

By AV Construction Group Corp. Published 4 min read

Illustration for articles about roofing

In short: a roof is more than shingles. The Owens Corning Total Protection Roofing System groups the parts of a roof by the job they do: seal, defend, breathe and comfort. The parts are made to work together, so swapping in any other part is a decision to make with care.

A roof is a system

When people think of a roof, they think of shingles. But the shingles are only the top layer. Under them there are layers that keep water out. At the edges and the top there are special shingles. Under the roof deck, air has to move through the attic.

Owens Corning calls its way of putting these parts together the Total Protection Roofing System. It groups the parts by the job each one does. Here they are, one by one.

Seal: the layers under the shingles

The first job is to keep water away from the roof deck, the wood that holds the roof. Owens Corning lists two parts for this:

  • Ice and water barrier: a membrane for the places where water is most likely to get in.
  • Synthetic underlayment: a layer that covers the deck under the shingles.

Owens Corning describes these two as a two-part protection that helps keep moisture away from the deck. If water gets past the shingles, these layers are the next line of defense.

Defend: three kinds of shingles

The second job is the one people see. Owens Corning lists three kinds of shingles, each for a different part of the roof:

  • Starter shingles: they go at the edges, under the first row.
  • Shingles: the main field of the roof.
  • Hip and ridge shingles: they cover the hips and the top of the roof.

Each kind is shaped for its place. Owens Corning says the three work together for specialized protection on each part of the roof.

Breathe: air in, air out

The third job happens out of sight, in the attic. Owens Corning lists:

  • Intake ventilation: openings, usually low on the roof, that let air in.
  • Exhaust ventilation: openings, usually high on the roof, that let air out.

Owens Corning explains that proper ventilation helps create a balanced flow, where warm, humid air is replaced by cool, dry air. In a hot, humid climate like South Florida, that balance matters.

Comfort: the attic

The fourth group is about the home below the roof. Owens Corning lists blown-in attic insulation as part of the system, for comfort and performance. It is not part of every roofing job, but it is part of the full picture.

Why the parts are made to work together

Each part does one job, and each job depends on the others. The underlayment works with the shingles. The starter shingles help the first row stay in place. The vents work with the attic. A weak link in one part can affect the rest.

When one manufacturer designs the parts as a set, it can write instructions for the whole set. The installer then follows one set of rules instead of guessing how different products fit.

Why not mix in any other part

There are two practical reasons to be careful about mixing parts.

The warranty. Owens Corning's roofing system warranties need a set of its own components, such as hip and ridge shingles, underlayment and other accessories. If other parts are used, a system warranty may not apply. Some coverage on Duration shingles also depends on Owens Corning parts, such as an approved hip and ridge product and starter shingles at the eaves and rakes.

The fit. Parts made for the system are made to work with each other. A different part may work too, but nobody has checked it as part of that set.

This does not mean every roof must use every part. It means the choice should be made on purpose, in writing, before the work starts.

What to ask your contractor

  • Which parts of the system will my roof have?
  • Which underlayment and which ice and water barrier will you use?
  • Will the starter and the hip and ridge shingles match the system?
  • How will the attic be ventilated?
  • Which warranty applies with these parts, and who registers it?

Our Owens Corning listing shows a TPRS training badge, which points to training on this system.

Next step

Start with a preliminary estimate online, or request a visit. The final price is confirmed after a site visit, in a formal proposal. Read more on our Owens Corning page, and see our roofing services.

Sources

  1. Owens Corning - Total Protection Roofing System (viewed 2026-11-04)
  2. Owens Corning - Roofing warranties (viewed 2026-11-04)
  3. Owens Corning - TruDefinition Duration shingles (viewed 2026-11-04)

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Owens Corning Preferred Contractor: what it means for your roof

AV Construction Group Corp. is an independent contractor. Owens Corning and its trademarks belong to Owens Corning.

Keep reading

More guides on the blog