Skip to main content

Architectural vs three-tab shingles: how to read the spec sheet

What exposure, coverage per square, wind rating, algae resistance and warranty mean on a shingle data sheet, with Owens Corning examples and Florida approvals.

By AV Construction Group Corp. Published 7 min read

Illustration for articles about roofing

A shingle data sheet is a list of numbers, and each number answers a different question. Exposure and coverage tell you how much roof a bundle covers. The wind class, algae years and impact class are the manufacturer's laboratory ratings. The warranty name tells you which document to read. This article walks through those lines using three Owens Corning sheets as examples, and explains why in Miami-Dade and Broward the product approval matters as much as any of them. The figures below come from the manufacturer's sheets, viewed on 2026-11-04. They are laboratory classifications, not a promise of how a particular roof will behave in a storm. AV Construction Group works with Owens Corning products, and the manufacturer is one of its material suppliers.

What the lines on a sheet mean

Exposure is the part of each shingle left uncovered by the course above it. A larger exposure means each piece covers more roof. The sheets for the architectural lines list 5 5/8 inches. The traditional three-tab line lists 5 inches. The pieces-per-square figure gives the same information from another angle: 64 architectural shingles against 80 three-tab shingles for roughly the same area.

Coverage per square is how much roof the pieces cover. A roofing "square" is 100 square feet. The architectural sheets list 98.4 square feet from three bundles (64 shingles). The three-tab sheet lists 100 square feet and 80 shingles. The point is not that one is better. It is that a quote should be built from the measured roof, its slopes and a waste allowance, never from a rounded number of squares.

Wind classification shows the test class and a speed. The sheets cite ASTM D3161 Class F, and in some cases ASTM D7158, as the test methods. A manufacturer's top number is what the product reached in its own test setup, and a higher number is not automatically the right one for your roof, because the approval for your address decides which classification the permit lists. The Florida evaluation report for these shingles adds a limit that is easy to miss: its ASTM D7158 Class H classification applies only to exposure category B or C and buildings 60 feet tall or less.

Algae resistance is the number of years the manufacturer lists for resisting the dark streaks that algae cause. It is a claim about appearance, not about strength.

Impact class is the UL 2218 rating (Class 1 to 4). It is a hail-type test, covered in the Class 3 vs Class 4 article.

Warranty is a name on the sheet, such as "limited lifetime." The wording that matters is in the actual warranty document. See how long roofs last for why a warranty term is not a lifespan.

Three Owens Corning lines side by side

Line (type)ExposureCoverage per squareWind rating on the sheetAlgae resistanceImpact class on the sheetWarranty named
Duration (architectural, mid-range)5 5/8 in98.4 sq ft, 3 bundles, 64 shinglesup to 160 mph25 yearsClass 3 (UL 2218, FM 4473)Limited lifetime
Oakridge (architectural, economy)5 5/8 in98.4 sq ft, 3 bundles, 64 shingles110 or 130 mph25 yearsClass 3 (UL 2218)Limited lifetime
Supreme (traditional three-tab, economy)5 in, 12 x 36 in100 sq ft, 80 shingles60 mph10 yearsNo impact classification25-year limited

Per the Owens Corning sheets, all three list Florida and Miami-Dade approvals. Duration's sheet also names a nailing feature called SureNail, and a Designer color collection uses the same data as Duration. Two things stand out. The architectural lines list a larger exposure and higher wind and impact numbers. The traditional three-tab line lists a lower wind figure and no impact class. The right choice still depends on the house, the budget and what the permit requires.

Why the product approval matters in a hurricane zone

A data sheet is marketing-grade information. A product approval is a legal document that your building department accepts.

Outside Miami-Dade and Broward, the Florida Building Commission lists evaluation reports. The one for these shingles, FL10674-R19, says it is not for use in the High-Velocity Hurricane Zone (HVHZ), which the code defines as Broward and Miami-Dade Counties. It also says it covers above-deck components only, and it does not evaluate fire classification.

In the HVHZ the approval is a Miami-Dade Notice of Acceptance (NOA). Miami-Dade's NOA 26-0331.12 covers the Duration family (Duration, Duration Designer Colors, STORM and FLEX). It lists the following conditions:

  • Shingles are installed under Roofing Application Standard RAS 115, including its flashing and nailing details.
  • The roof mean height is not more than 33 feet.
  • Fire classification is not part of the acceptance. A separate roofing materials directory covers it.
  • Shingles carry the Miami-Dade seal or the wording "Miami-Dade County Product Control Approved."
  • The permit application includes a copy of the NOA.

The scope of that NOA does not list Oakridge or Supreme, so ask for the NOA number of the exact product proposed. Florida product approval and NOA explained shows how to read one.

The shingle is only one layer

Wind performance depends on the whole system: the deck and its nailing, the underlayment, the starter strip, the number and placement of nails, the ridge caps and the flashing. A top wind number on a bundle does not repair a weak deck. Secondary water barrier and underlayment explains the layer under the shingles, and wind mitigation inspections shows how the roof's features are recorded for insurance.

Questions people ask

Is architectural always better than three-tab?

On the numbers these sheets list, the architectural lines have a higher wind figure and an impact class, and the three-tab line has neither. That makes them the more common choice where wind is the main concern. "Better" still depends on the roof's slope, the deck, local requirements and what the budget allows, so ask your roofer to explain the choice for your house.

Does "160 mph" mean my roof will survive a 160 mph hurricane?

No. It is a laboratory classification for a shingle installed a specific way. It does not account for flying debris, an old deck or poor nailing. Ask which installation conditions sit behind the number.

What does "limited lifetime warranty" cover?

A data sheet does not say. Read the actual manufacturer warranty for the product and the installation method, including what it requires and excludes, before you rely on it. Warranties can carry conditions about installation and ventilation, so read them before the work starts.

Do I need the product's wind rating in writing?

Ask for the product name, the approval number that applies in your city and the wind classification the permit lists. They should match the label on the bundles.

Check before you decide

  • Ask for the exact product line and the sheet or approval document for it.
  • In Miami-Dade or Broward, ask for the NOA number and check its expiration and limits.
  • Confirm that the roof height and exposure fit the limits in the approval.
  • Ask what the quote assumes about waste and how the squares were counted.
  • Read the actual warranty document, not only its name.
  • Ask which underlayment, starter and ridge products complete the system.
  • Ask your roofing contractor to explain any rating in plain terms.

AV Construction Group works with Owens Corning products and counts the manufacturer among its material suppliers. If you would like a roof quoted with these materials, you can request a roofing estimate from AV, read about our roofing services or contact us.

The figures come from published manufacturer data sheets and public approvals. This article is general information, not engineering advice. Ratings and approvals change, so confirm details with the manufacturer and your building department.

Sources

  1. Owens Corning - TruDefinition Duration shingles (product data, viewed 2026-11-04)
  2. Owens Corning - Oakridge shingles (product data, viewed 2026-11-04)
  3. Owens Corning - Supreme three-tab shingles (product data, viewed 2026-11-04)
  4. Florida Building Commission product approval FL10674-R19 - Owens Corning asphalt roof shingles, non-HVHZ evaluation report (Revision 14, 10/23/2023)
  5. Miami-Dade County Product Control - Notice of Acceptance 26-0331.12 (Owens Corning TruDefinition Duration family)

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog