Older South Florida homes and condos can still have original cast iron drain lines and aging supply piping. Slow drains, backups, sewer odors, repeated leaks and weak pressure are common warning signs. A camera inspection and a pressure test show what condition the pipes are in, and the repair options range from spot fixes to full replacement with PEX, CPVC, copper or PVC, all done under a permit and the Florida Building Code, Plumbing.
Which pipes are involved?
A building has two separate systems, and they age differently.
- Supply piping brings pressurized drinking water to fixtures. Older buildings may have copper, galvanized steel or early plastic.
- Drain, waste and vent (DWV) piping carries wastewater away by gravity. In older buildings this is often cast iron.
A home inspection company serving South Florida describes cast iron drain lines under the slab as common in homes built from the 1950s to the late 1970s. Treat that as a rough guide, not a rule. The only way to know is to inspect the building.
Signs of a failing cast iron drain
Cast iron is strong, but it corrodes from the inside. A municipal utility guide on sewer pipe describes wastewater flow etching the bottom of the pipe, which thins the wall, lets debris in and wastewater out, and can eventually lead to sagging sections and collapse. The same guide puts an average life for cast iron sewer pipe at roughly 30 to 50 years. That figure comes from a California utility, not Florida, so use it only as a general reference.
Signs to watch for:
- Slow drains or repeated backups on more than one fixture
- Gurgling toilets or drains
- Sewer odors indoors
- Water stains, mold or damp areas on floors or walls near drain lines
- A sunken or damp spot on a slab
Signs of aging supply piping
- Repeated leaks, especially several in a short time
- Weak pressure at fixtures
- Visible corrosion at joints or fittings
- Water bills that rise without a change in use (see slab leak signs and detection)
Lead is a separate concern. The EPA notes that lead can come from older service lines, lead solder and some brass fixtures. If you suspect lead, ask your water utility or a licensed plumber, and consider having the water tested.
How pipes are checked
- Camera inspection. A small camera is run through the drain line to look for corrosion, cracks, offsets, roots, blockages and collapse. Ask for the recording.
- Pressure test. A supply line that cannot hold pressure has an active leak.
- Hydrostatic test. Filling a drain section with water checks whether it leaks.
Repipe options compared
The Florida Building Code, Plumbing is adapted from the International Plumbing Code, and its pipe tables list the allowed materials with the product standards each must meet. A model-code table for water service pipe, for example, lists CPVC, copper, PEX, PVC, polyethylene, polypropylene, stainless steel and others, each tied to specific ASTM or other standards. Which material is allowed for which use, and in which size, is set by the adopted code, so the table in the edition that applies to your permit controls.
| Material | Typical use | Practical notes |
|---|---|---|
| PEX (cross-linked polyethylene) | Water supply | Flexible tubing, often installed with a manifold. Must be protected from sunlight; manufacturers rate UV resistance in months, and it should be stored indoors until installed. |
| CPVC | Water supply | Rigid plastic joined with solvent cement. Needs room for expansion and must be kept away from incompatible materials, such as the plasticizers in some vinyl or rubber hangers. |
| Copper | Water supply | Long-used metal tube. Fittings and solder must meet lead-free requirements, which the EPA defines as a weighted average of 0.25 percent lead or less on wetted surfaces. |
| PVC and ABS | Drain, waste and vent | Plastic drain pipe with solvent-welded joints. The code has joint requirements for each. |
| Cast iron | Drain, waste and vent | Present in many older buildings. Whether to keep, repair or replace it depends on what the inspection shows. |
No material is best in every case. A contractor should explain why a material suits your building: access, fire-rated penetrations, noise, local water conditions, and how long the work will take.
Repair versus replace
For drains, a damaged section can sometimes be cut out and replaced, or the line can be lined or replaced entirely. Lining a building sewer is addressed in the plumbing code: the 9th Edition reserves its old relining section and adds a new section for cure-in-place rehabilitation, referencing ASTM F1216 or F1743. Check with the building department which approach is accepted for your project today.
What the code says now
- The 8th Edition (2023) Florida Building Code is the edition currently in force.
- The 9th Edition (2026) takes effect on December 31, 2026. Miami-Dade states that applications and plans submitted on or after that date must meet the new edition.
- The 9th Edition Plumbing volume is based on the 8th Edition and uses the 2024 International Plumbing Code as its model, though not all of its changes were adopted. Among its changes are updates to PEX and CPVC reference standards and a new requirement that water heaters in potable systems meet a lead-content standard.
If your project may straddle that date, ask the contractor which edition will apply.
Permits and licensing
In unincorporated Miami-Dade, altering or repairing plumbing requires a permit. The county's permit page does not mention repiping specifically, so confirm with the office that covers your address. Municipalities issue their own permits.
A Florida plumbing contractor's license covers the full plumbing trade, including drainage and water and sewer lines. Check that the license is active before you sign.
Condos: who owns which pipe?
In a condominium, Florida law says the association maintains the common elements, except limited common elements that the declaration assigns to unit owners. Which pipes count as common elements, and who pays to replace them, depends on your declaration. Boards and owners should read it, and may want to ask an attorney, before planning a building-wide project.
Questions people ask
Do I have to replace cast iron pipe?
Not automatically. If a camera inspection shows the pipe is sound, it may remain in service. Replacement is usually discussed when there is corrosion, collapse, repeated backups or leaks.
Is PEX allowed in Florida?
PEX is listed in the model code's pipe table and the Florida code references PEX standards. Confirm with the building department for your property and how it must be protected and installed.
Can I repipe one unit in a condo on my own?
Possibly, but first read your declaration and rules, since some pipes are common elements. A permit and a licensed contractor are still required for the work.
How long does a repipe take?
It depends on access, the size of the building and how many fixtures there are. Ask for a schedule that includes wall repair and inspections.
Check before you decide
- Get a camera inspection or pressure test before choosing a material.
- Ask why the contractor recommends PEX, CPVC, copper or PVC for your building.
- Confirm the license, permit and which Florida Building Code edition applies.
- Ask how wall, ceiling and floor repair is included.
- In a condo, check the declaration and notify the association.
See plumbing services for the trade overview.
