Skip to main content

Backflow prevention and annual testing in Miami-Dade

What a backflow preventer does, which Miami-Dade properties need one, why annual testing by a certified tester is required, and how results are reported.

By AV Construction Group Corp. Published 6 min read

Illustration for articles about plumbing

A backflow preventer is a device that keeps water from flowing backward from a building's plumbing into the public drinking water supply. In Miami-Dade, certain customers, such as properties with lawn irrigation, fire sprinkler systems and some commercial uses, must install an approved assembly. The assembly must be tested when installed and every year after by a certified backflow tester, and the results go to the county's Cross-Connection Control Unit.

What backflow is

A cross-connection is any link between drinking water and something that is not safe to drink. Backflow is the unwanted reversal of flow that can pull that material into the water supply. Miami-Dade Water and Sewer (WASD) names two causes:

  • Backpressure, when pressure downstream is higher than the supply pressure
  • Backsiphonage, when supply pressure drops below atmospheric pressure

WASD gives everyday examples: a garden hose left in soapy water, a kitchen sprayer in a dirty sink, irrigation systems, and boilers.

Types of backflow prevention

WASD lists four assembly types and where each is typically used:

AssemblyTypical use
Reduced Pressure Principle (RP)Domestic water service connections
Double Check Valve (DCVA)Fire suppression systems
Double Check Detector (DCDA)Fire suppression systems
Pressure Vacuum Breaker (PVB)Lawn irrigation systems

An air gap, a clear vertical space between a faucet outlet and the vessel it fills, is the simplest form of protection. WASD notes it is the least expensive form and that removing the cross-connection altogether is preferred when possible.

When Miami-Dade requires one

Miami-Dade County Code, Chapter 32, Article VIII, requires certain customers to install a backflow prevention assembly on their water service. The requirement depends on the hazard level, the type of service (domestic, fire or irrigation), and how the facility is used. WASD's examples include hospitals, adult congregate living facilities, service stations, auto repair shops and customers with lawn irrigation. The county says this list is not exhaustive.

Two points matter for owners:

  • Irrigation. A lawn irrigation system needs a pressure vacuum breaker at the service connection. WASD's brochure says existing customers were required to have one by June 1, 2016.
  • Existing customers. For other existing customers, Section 32-154 of the code set earlier deadlines, June 1, 2007 and January 1, 2012.

If you are not sure whether your service needs an assembly, ask WASD's Cross-Connection Control Unit rather than assuming. The county brochures read for this article date from the mid-2010s, so confirm that the details still apply.

Annual testing

WASD says the assembly must be tested when installed and then every year by a Certified Backflow Prevention Assembly Tester. Annual testing matters because mechanical parts can wear, foul or be bypassed. A UF training center explains that mechanical devices are tested with calibrated gauge equipment, while an air gap needs only a visual check.

Florida's drinking water rules also address cross-connections. Rule 62-555.360 of the Florida Administrative Code prohibits cross-connections and requires community water systems to run a cross-connection control program. Local utilities such as WASD apply their own county code on top of that.

Commercial properties

The county sets requirements by hazard level and use, not by a simple "commercial" label, so a commercial property should not assume it is exempt or covered. Businesses with fire sprinkler systems, irrigation, boilers or processes that handle chemicals should ask WASD what applies to each service line. WASD's testing requirement applies to each required assembly.

Who may install and who may test

  • Installation and repair. A licensed plumber or contractor must install the assembly to WASD standards. A UF training center notes that Florida law requires a state-licensed plumbing contractor, under Chapter 489, to install or repair backflow assemblies on domestic water systems. Fire protection assemblies fall under separate rules involving licensed fire sprinkler contractors under Chapter 633.
  • Testing. Only a certified tester may test. WASD says it keeps a partial list of testing providers and publishes a directory of companies with certified testers. The directory contains duplicate entries and some companies outside the county, so call the unit to verify a tester.
  • Certification. The UF program says testers recertify every two years. Individual utilities may add their own requirements, so ask WASD what it accepts.

Permits and reporting

  • A permit for installing the assembly is required from the building department of the municipality where the work is done, and that department sets the fee.
  • Test results must be submitted on an approved test form to WASD's Cross-Connection Control Unit. WASD lists three ways: mail to 1001 NW 11th Street, Miami, FL 33136; fax at 786-268-5485; or email at ccc@miamidade.gov. Its hotline is 305-547-3046.

Ask the tester whether they submit the form or you do, so that nothing is missed.

The plumbing code side

The Florida Building Code, Plumbing, has its own backflow rules inside buildings, for example for hand showers and water dispensers. The 9th Edition (2026), which takes effect December 31, 2026, updates backflow-related tables and adds standards for some devices. These in-building rules are separate from the utility's requirement for a protective assembly at the service connection. See aging pipes and repiping for how code editions affect permits.

What affects cost

WASD says each company sets its own prices and recommends getting several quotes. Factors include the type and size of the assembly, access, whether the assembly passes or needs repair, and whether the tester files the report for you.

Questions people ask

Does my home need a backflow preventer?

It depends on the hazard level, the type of service and how the property is used. A lawn irrigation system is one of the examples WASD gives. Check with WASD for your account.

What happens if the assembly fails the test?

A failed assembly would normally be repaired or replaced by a licensed contractor and then retested. Ask the tester how a failed result is handled with the county.

Can I test my own assembly?

WASD says only a certified tester may test. Certification is a defined credential, not a matter of general plumbing skill.

How do I find a certified tester?

WASD keeps a partial list of providers and a directory of companies with certified testers. Call the Cross-Connection Control Unit at 305-547-3046 to confirm a name before you hire.

Check before you decide

  • Ask WASD whether each of your service lines needs an assembly.
  • Confirm that the tester is certified, and ask for a copy of the report.
  • Mark the annual test date and confirm who submits the form.
  • Use a licensed contractor for installation or repair and get a permit.
  • Compare written quotes.

See plumbing services for related work.

Sources

  1. Miami-Dade Water and Sewer: Cross-Connection and Backflow brochure
  2. Miami-Dade Water and Sewer: Backflow Prevention Assembly Installation
  3. Miami-Dade Water and Sewer: Backflow Prevention Installation for Lawn Irrigation Systems
  4. Miami-Dade Water and Sewer: Certified Backflow Prevention Assembly Testers directory
  5. UF TREEO Center: Backflow Prevention Program
  6. Florida Building Commission: Analysis of Changes, 9th Edition (2026) FBC Plumbing

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog