Skip to main content

Slab leak signs, detection and repair options in Florida

How to spot a slab leak, confirm it with your water meter, how professionals pinpoint it, and the main repair options for Florida slab-on-grade homes.

By AV Construction Group Corp. Published 7 min read

Illustration for articles about plumbing

A slab leak is a leak in a water supply or drain line that runs in or under a concrete slab floor. The usual first clues are a water meter that keeps moving when everything is off, a higher bill with no change in use, warm spots on the floor, or the sound of running water in a quiet house. A meter test confirms whether water is escaping, and a licensed plumber can then pinpoint the leak and propose a repair.

What a slab leak is

In a home built on a concrete slab, some water supply lines and the drain lines can run in or beneath the concrete. When one of those pipes leaks, the water has nowhere obvious to go, so the problem can go unnoticed for a while.

Not every leak at floor level is a slab leak. Look-alikes include a running toilet, a leaking hose bib, an irrigation zone, a leak at the base of the water heater, and an air conditioner condensate line. A good plumber rules these out first.

Common signs

Watch for these clues:

  • A water bill that rises with no change in how you use water
  • A meter dial or flow indicator that moves when no water is running
  • Warm spots on the floor, which can point to a leak on the hot-water side
  • The sound of running water when the house is quiet
  • Weak pressure at fixtures
  • Damp flooring, lifting flooring, or musty odors near a wall base

No single sign proves a slab leak. The meter test below is the first step.

How to check with your water meter

Miami-Dade Water and Sewer (WASD) describes a simple test you can do yourself:

  1. Make sure no water is running anywhere in the home or yard.
  2. Look at the meter's flow indicator. If it is moving, water is going somewhere.
  3. If there is no indicator, or it is still, write down the register reading, wait two hours without using water, and read it again. A higher number suggests a leak.
  4. To narrow it down, close the house shutoff valve and repeat. If the meter still moves, the leak is likely in the service line outside the home or at an outdoor fixture. If it stops, the leak is likely inside.

The EPA's WaterSense program describes the same two-hour approach. For toilets, WASD suggests adding dye to the tank and waiting about 20 minutes without flushing to see if color reaches the bowl.

Who is responsible past the meter? WASD says it maintains the service up to and including the meter box. The account holder is responsible for water used beyond it, including leaks that are concealed or underground. WASD does not repair private property.

How plumbers pinpoint the leak

Once the meter confirms a leak, a professional narrows down where it is. According to a 2026 trade article, a typical process looks like this:

  • Isolation. Closing the cold-water inlet at the water heater shows whether the leak is on the hot or cold side. A pressure test of the isolated line shows whether it holds pressure.
  • Acoustic detection. A ground microphone or listening disc picks up the sound of water escaping under pressure. Hard flooring carries sound well. Carpet and thick pad make it harder.
  • Thermal imaging. A camera shows warm areas from hot-side leaks. It is less helpful for cold-water leaks, so another method should confirm.
  • Tracer gas. A non-flammable gas is introduced into the line, and a sensor finds where it escapes. This can help on plastic lines.
  • Camera and hydrostatic testing for drains. If a supply line holds pressure, the problem may be a drain line. A water-filled test and a camera inspection can check it.

Before anyone cuts concrete, the area should be scanned for rebar, post-tension tendons and conduit. The same article describes ground-penetrating radar and rebar locators for this. Tracing the actual pipe route, rather than trusting old drawings, helps keep the opening small.

Repair options

The right option depends on the pipe material, how many leaks there have been, and what the floor finish is.

OptionWhat it involvesTends to suit
Spot repairOpen the slab at the pinpointed spot and fix the failed sectionOne isolated leak in otherwise sound pipe
RerouteAbandon the leaking run and install new pipe overhead or in wallsRepeated leaks, or a line that is hard to reach
RepipeReplace a larger portion or all of the supply pipingPipes at the end of their life, with leaks likely to return

The trade article advises weighing floor restoration, disruption to the household, and the chance of future leaks, not only the immediate price. After any repair, the system should be re-pressurized and the meter checked to confirm it is still.

For older piping, see aging pipes and repiping in South Florida.

Permits and licensing

In unincorporated Miami-Dade, altering or repairing plumbing requires a permit, and only a licensed contractor or an owner-builder can pull one. Cities within the county issue their own permits, so confirm which office covers your address.

Under Florida law, a plumbing contractor's scope covers the full plumbing trade, including drainage, water and sewer lines. Work outside that trade must be handled by the right licensed contractor. Ask to see the license and confirm it is active before work starts.

What affects cost

Costs vary widely, and any figure found online should be treated with caution. These factors drive the price:

  • How deep or hard to reach the leak is
  • The floor finish that has to be removed and replaced
  • Whether the leak is on a supply or drain line
  • How many leaks have occurred, and whether the pipe is failing along its length
  • Whether the leak detection, repair, and floor restoration are quoted separately
  • Whether a permit and inspection are required

Ask for a written scope that lists each of these, so quotes can be compared fairly. Insurance coverage for leak detection, access, and restoration depends on the specific policy, so read yours and ask your insurer before work begins.

Questions people ask

Can I find a slab leak myself?

You can confirm that a leak exists with the meter test and sometimes tell whether it is inside or outside the house. Pinpointing the exact spot under concrete normally requires professional equipment.

Is a slab leak an emergency?

A leak can keep running day and night and may damage flooring and walls. Many homeowners close the main shutoff valve until a plumber arrives. If water is near electrical equipment, stay clear and call a licensed professional.

Does a slab leak always mean the whole house must be repiped?

No. A single leak in pipe that is otherwise sound may be handled with a spot repair. Repeated leaks or pipe that is deteriorating more broadly are the cases where rerouting or repiping is usually discussed.

Will the plumber need to cut the floor?

Often yes for a spot repair, though the opening can be small if the leak is pinpointed well. Rerouting avoids opening the slab at the leak, but may need access through walls or ceilings.

Check before you decide

  • Do the meter test and write down the results.
  • Ask whether the leak is on the hot or cold side, or in a drain.
  • Ask how the leak will be pinpointed and how the slab will be scanned before cutting.
  • Get the options in writing: spot repair, reroute, and repipe, with pros and cons.
  • Confirm the contractor's license and who pulls the permit.
  • Ask how floor and wall restoration is handled and who does it.

For background on the trade itself, see plumbing services.

Sources

  1. Miami-Dade Water and Sewer: Leak Detection Using the Water Meter
  2. US EPA WaterSense: Fix a Leak Week
  3. Contractor Magazine: Pinpoint the Slab Leak Before You Break the Floor (August 2026)
  4. Miami-Dade County: How to Apply for a Building Permit
  5. Florida Statutes 489.105: Definitions (Contracting)

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog