Skip to main content

Low-slope residential roofs: when shingles are not the answer

The Florida Building Code's minimum slope for asphalt shingles, what a low-slope home roof is, and the membrane systems used below 2:12, with DeckSeal data.

By AV Construction Group Corp. Published 7 min read

Illustration for articles about roofing

Asphalt shingles are allowed only on roofs with a slope of 2:12 or more, according to the Florida Building Code, Residential, 8th Edition (2023). A roof flatter than that needs a different kind of covering: a membrane system that is sealed rather than shingled. This article explains what slope numbers mean, what the code says about shingles and about the low-slope systems, and what an Owens Corning data sheet shows for a residential low-slope system called DeckSeal (viewed 2026-11-04). Those figures are the manufacturer's published data, not a promise of how a roof will perform in a storm. AV Construction Group works with Owens Corning products, and the manufacturer is one of its material suppliers. Commercial flat roofs have their own article, commercial flat roof systems, so this one stays with homes.

What the slope numbers mean

Slope is written as rise over 12 inches of run. A 2:12 roof rises 2 inches for every 12 inches across, which is about 17 percent. A 1/4:12 roof rises a quarter of an inch per foot, which the code calls a 2 percent slope. So "low slope" at a house means a roof between nearly flat and just under 2:12. It can show up on porches, additions, carports and flat sections between higher roofs.

The line matters because most of the rules in the roofing chapter change at 2:12. The code's underlayment rule opens with "roof slopes 2:12 and greater," and the secondary water barrier rule has an exception for roofs under 2:12 that have a continuous roof system. The first is covered in the secondary water barrier article.

What the code says about shingles

Section R905.2.2 of the residential code says asphalt shingles shall be used only on roof slopes of two units vertical in 12 units horizontal (2:12) or greater. That section has no double-underlayment rule. Underlayment is handled in Section R905.1.1.1, which allows three methods: self-adhering polymer-modified bitumen underlayment over the entire roof deck, self-adhering strips at least 3 3/4 inches wide over all deck joints with an approved underlayment over the whole roof, or two layers of mechanically fastened underlayment. Table R905.1.1.1, which applies when the deck joints are taped, calls for the two-layer method (Item 3) on slopes from 2:12 up to less than 4:12, and for a single layer lapped 4 inches, shingle fashion, on slopes of 4:12 and greater. The full-deck self-adhered method has no slope split. Earlier editions put a double-underlayment sentence in the slope section, and a public comment during the 2023 code cycle said it should have been deleted when the underlayment requirements were updated.

In Miami-Dade and Broward the High-Velocity Hurricane Zone rules apply. Miami-Dade's summary of its 2023 roofing changes uses the same 2:12 threshold for underlayment, and each product's approval sets its own limits.

What the code says about low-slope systems

For slopes under 2:12 the code lists membrane systems, each with a minimum design slope. These are the figures from Chapter 9 of the residential code.

SystemMinimum design slope in the code
Asphalt shingles2:12
Built-up roof1/4:12 (coal-tar built-up: 1/8:12)
Modified bitumen1/4:12
Thermoset single-ply membrane1/4:12
Thermoplastic single-ply membrane1/4:12
Metal panels, lapped seams without sealant3:12
Metal panels, lapped seams with sealant1/2:12
Metal panels, standing seam1/4:12

Two details are easy to miss. First, a reroof is exempt from the 1/4:12 minimum design slope where the roof has positive drainage, under Section R908.1. Second, Miami-Dade's table for the High-Velocity Hurricane Zone allows standing seam metal systems that pass certain leakage tests (FM 4471 Appendix G or ASTM E2140) down to a 1:12 slope. That is a different number from the residential chapter, so the zone's rules and the product approval decide which one applies to your roof.

Systems used between 1/4:12 and 2:12

Between those two slopes, the systems include modified bitumen membranes, which can be self-adhered or mechanically attached, and single-ply membranes. Self-adhered means the layers bond to each other and to the deck. Mechanically attached means a base layer is fastened to the deck and the top layers are applied over it. The choice depends on the deck, the existing roof, the building department and the product approval.

DeckSeal as an example

Owens Corning lists DeckSeal as a self-adhered reroofing system for homes on slopes from 1/4:12 to 2:12, built in two or three plies.

LayerProductRoll sizeThicknessCoverage listed
Top plySA SBS Cap32 ft 10 in x 39 3/8 in130 milsAbout 100 sq ft
Base plySA Base/Ply65 ft 8 in x 39 3/8 in80 mils200 sq ft
Mechanically attached baseMA NailBaseSame size as the base ply80 milsSame as the base ply

A mil is a thousandth of an inch, so 130 mils is 0.13 inch. The coverage figures are lower than length times width, which would give about 108 and 215 square feet. A quote should be built from net coverage, so ask how many rolls of each layer the proposal counts.

The sheet describes a system, not a single product. The choice between two plies and three, and between the self-adhered and the nailed base, is part of the specification for your roof. Do not assume a system sold for reroofing applies to a roof with an unusual deck. Ask the roofer to state in the contract how many plies are proposed and why, and which approval document lists that combination for your slope.

Questions people ask

My roof is 1.5:12. Can I put shingles on it?

Not under the 8th Edition's R905.2.2, which asks for 2:12 or more. Ask your building department what is acceptable for that slope and which product approval covers it.

Is the code's slope the only limit?

No. The code number is the floor. A product approval can add its own limits, as Miami-Dade's Notice of Acceptance for Owens Corning shingles does with a 33-foot roof mean height, so read the approval for the exact product, and check it against your slope and your building.

How do I find my roof's slope?

A licensed roofer or an inspector can measure it. Ask for the number in the proposal in the form "X:12" for each roof area.

Does a low-slope roof drain differently?

Yes. Low-slope roofs rely on a continuous membrane and on drainage, so the details around drains, edges and penetrations matter. See flashing and penetrations.

Is a low-slope roof covered by the 25 percent rule when only part of it is damaged?

The rule depends on how much of the roof is repaired or replaced. Read the 25 percent rule article and ask the building department how your scope is classified.

Check before you decide

  • Ask for the slope of each roof area in "X:12" form.
  • Confirm which system and which product approval covers that slope.
  • In Miami-Dade or Broward, ask for the Notice of Acceptance and read its limits.
  • Ask how many plies the system has and how the deck is prepared.
  • Ask how the quote counts rolls and laps.
  • Ask about drainage, drains and edge details.
  • Ask your roofing contractor why shingles are or are not allowed on each part of the roof.

AV Construction Group works with Owens Corning products and counts the manufacturer among its material suppliers. If you would like a roof quoted with these materials, you can request a roofing estimate from AV, read about our roofing services or contact us.

The figures come from published manufacturer data sheets and public approvals. This article is general information, not engineering advice, and codes and approvals change, so verify details with your building department.

Sources

  1. Florida Building Code, Residential, 8th Edition (2023), Chapter 9 - Sections R905.1.1, R905.2.2, R905.9 to R905.13 and R908
  2. Miami-Dade County - 2023 FBC roofing code changes (HVHZ Chapter 15, Table 1515.2 and Section 1518.2)
  3. Florida Building Commission - 2023 code development, Roofing detail report (second comment period, R905.2.2)
  4. Owens Corning - DeckSeal self-adhered low-slope system (product data, viewed 2026-11-04)

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog