Skip to main content

Secondary water barrier and roof underlayment in Florida

What a secondary water barrier is, when the Florida Building Code requires one on a reroof, and how the Miami-Dade HVHZ underlayment rules differ.

By AV Construction Group Corp. Published 6 min read

Illustration for articles about roofing

A secondary water barrier is a backup layer under the roof covering that is meant to keep rain out of the house if wind strips off the shingles, metal or tile. Under the Florida Building Code, 8th Edition (2023), a secondary water barrier is required when a roof covering is removed and replaced, with exceptions for very low slopes and for tile systems installed as the code describes. In Miami-Dade's High-Velocity Hurricane Zone (HVHZ), the underlayment rules sit in a separate chapter, so your permit drawings and product approvals follow the HVHZ text.

What a secondary water barrier does

The visible roof covering takes the weather first, and in a hurricane it is often the first thing to fail. The Florida Division of Emergency Management describes the secondary water barrier as the layer that should stay attached when the primary cover blows off, so the attic stays dry. The same page notes that ordinary 15-pound felt can blow off at roughly 110 mph, even when new, which is why it is not treated as a dependable backup.

Water that gets past a lost roof cover can ruin insulation, ceilings and electrical systems even when the structure itself survives. A sealed layer over the deck seams limits that damage.

What the code requires on a reroof

Florida's reroofing rules are in the Existing Building volume. According to a Boca Raton Building Department packet built on the 8th Edition (2023), section 706.7.2 says that when a roof covering is removed and replaced, a secondary water barrier must be installed under the underlayment sections of the Building volume (1507.1.1) or the Residential volume (R905.1.1).

Key points from that packet:

  • Roofs with a slope below 2:12 that have a continuous roof system are treated as already compliant.
  • Clay and concrete tile systems installed as the code requires are deemed compliant.
  • For asphalt shingles, metal panels or shingles, mineral-surfaced roll roofing and slate-type coverings, you choose one of three methods.

The 8th Edition took effect on December 31, 2023, according to the Florida Building Commission.

The three common methods

Miami-Dade's summary of its 2023 roofing changes lists three approaches for the HVHZ (section 1518.2), and the Boca Raton packet lists the same three for its non-HVHZ reroofs:

  1. Self-adhered underlayment over the whole deck. A self-adhering polymer-modified bitumen sheet that meets ASTM D1970, installed under both the underlayment and roof-covering manufacturers' instructions.
  2. Taped or sealed deck joints. A strip at least 3-3/4 inches wide over every joint between sheathing panels, then an approved underlayment on top. Miami-Dade's summary notes that slopes under 4:12 need double-coverage underlayment with this method.
  3. Two layers of nailable underlayment. Layers of an approved felt or synthetic type, fastened with cap nails at spacings the code sets. Miami-Dade's summary calls for metal caps where the ultimate design wind speed is 170 mph or more.

Each method depends on product approvals and on installing exactly what the approval says. Mixing components from different systems can leave a roof that does not match its permit.

HVHZ versus the rest of Florida

The HVHZ covers Miami-Dade and Broward counties. The Florida Roofing and Sheet Metal Contractors Association (FRSA) wrote that the 8th Edition brought underlayment practices already used in most Florida counties into the HVHZ sections. Miami-Dade's own summary also adds specific tile-underlayment language: tile underlayment must be tested under TAS 103 and TAS 104, and a Notice of Acceptance (NOA) is required for all tile underlayment other than the traditional 30/90 type.

FRSA also reported, in a 2023 article, a disagreement with Miami-Dade over how tile underlayment uplift should be tested and listed. The article does not say how that was resolved, so confirm current practice with the Miami-Dade building department rather than relying on a trade article from 2023.

Tile, flat and metal roofs

  • Tile. Underlayment under tile is the real waterproofing layer, and the tile system has its own rules in the HVHZ. Tile systems are generally treated as meeting the secondary water barrier requirement when installed as the code requires.
  • Low-slope and flat roofs. Below 2:12, the continuous membrane is the waterproofing. These systems are covered by their own approvals.
  • Metal panels and shingles. These are listed with asphalt shingles in the three-method rule above, so one of those methods applies.

Edition changes to watch

The Ninth Edition (2026) of the Florida Building Code takes effect on December 31, 2026. Miami-Dade has said that permit applications and plans submitted on or after that date must follow it, and that online submissions after 4 PM on December 30, 2026 are also held to the new edition. I did not find a published change to the secondary water barrier rule in the sources I reviewed, but code text can change before final publication. If your permit will be filed near the end of 2026, ask which edition applies.

Questions people ask

Do I need a secondary water barrier if I am only repairing the roof?

The reroofing section applies when a roof covering is removed and replaced. Small repairs are handled differently, and the amount of work can bring other rules into play. Read the 25% rule article and ask the building department how your scope is classified.

Is peel-and-stick underlayment required everywhere?

No. The code allows several methods, and the self-adhered full-deck option is only one of them. The state emergency management page notes that some jurisdictions bar directly adhered membranes, so follow the product approval and the local building department.

Does a secondary water barrier lower my insurance premium?

That depends on the insurer and on how the roof is documented. The Florida Division of Emergency Management notes that some insurers may not accept every method for premium credits. See wind mitigation inspections for how roof features are recorded.

Who checks this work?

The building department does, through the permit and inspections. Miami-Dade's roof inspection checklist includes a stage before the anchor sheet is covered, where inspectors look at items such as sheathing re-nailing and underlayment. See roof permit requirements in Miami-Dade.

Check before you decide

  • Ask which secondary water barrier method is in the contract and which product approval number covers it.
  • Confirm the product has a current Miami-Dade NOA if the property is in the HVHZ.
  • Ask how deck joints and nail patterns will be handled before underlayment is installed.
  • Confirm the permit edition if filing near December 31, 2026.
  • Verify the contractor's license on the state's license search before signing.

A licensed roofing contractor can walk through these choices against your roof type and slope.

Sources

  1. Miami-Dade County - Roof inspection checklist
  2. Miami-Dade County - 2023 FBC roofing code changes (HVHZ)
  3. City of Boca Raton Building Department - Secondary water barrier packet (FBC 8th Edition, Existing Building 706.7.2)
  4. Florida Division of Emergency Management - Reroofing and the secondary water barrier
  5. Florida Roofing and Sheet Metal Contractors Association - A weak link in Florida's roofing underlayment requirements
  6. Florida Building Commission - Florida Building Code, 8th Edition (2023) effective date
  7. Miami-Dade County - Notice about the Ninth Edition Florida Building Code

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog