Skip to main content

Roof recover vs full tear-off under the Florida code

When Florida's building code allows a new roof over an existing one and when it requires full tear-off, including how Miami-Dade's HVHZ differs.

By AV Construction Group Corp. Published 6 min read

Illustration for articles about roofing

A roof recover puts a new covering over the existing one. Outside the High-Velocity Hurricane Zone (HVHZ), the Florida Building Code allows it only if none of a list of conditions applies: for example, a water-soaked base, two or more existing coverings, or certain heavy tile. In Miami-Dade, the code sends HVHZ buildings to a separate set of sections (1512 through 1525), so the rules are set by the HVHZ text, product approvals, and the building department's review of your specific roof.

Key terms

The Florida Building Code, Existing Building volume, defines reroofing as either recovering or replacing a roof covering. According to the Florida Roofing and Sheet Metal Contractors Association (FRSA):

  • Recover means adding a new covering over a prepared existing roof without removing it.
  • Replacement (tear-off) means removing the existing covering, repairing damaged substrate, and installing a new one.

Collier County's published summary of the 7th Edition (2020) adds that a recover is limited to a maximum of two layers of roof covering, subject to the conditions in section 706.3.

When the code requires tear-off

Section 706.3 of the Existing Building volume says new roof coverings may not be installed without first removing all existing layers down to the deck if any of these apply. FRSA's 2026 commentary shows the list as follows:

  1. The existing roof is water soaked or deteriorated so much that it is not adequate as a base. Wet insulation and corroded fasteners are the usual examples.
  2. The existing covering is wood shake, slate, or clay, cement or asbestos-cement tile.
  3. Two or more applications of any roof covering already exist.
  4. Blisters are present, unless they are cut or scraped open and the remaining material is secured first.
  5. The existing roof would be the attachment base for the new system, and the securement rules of section 1504.1 cannot be met.

Exceptions in the same section include:

  • Buildings in the HVHZ follow sections 1512 through 1525 instead.
  • A complete, separate system that carries its loads to the structure and does not rely on the existing roof, such as standing-seam metal, does not require removal.
  • A new protective coating over existing spray polyurethane foam does not require removal.

The 2022 FRSA article I used for background applies to the 7th Edition (2020). FRSA's 2026 commentary describes items 2 through 5 and these exceptions as unchanged going into the 9th Edition. I did not fetch the 8th Edition text itself, so confirm the exact wording with your building department.

Why these rules exist

A recover relies on the old roof as part of the new assembly. If the old roof holds water, the trapped moisture does not go away. FRSA notes that adhered systems over older attachment methods often fail current uplift requirements, which is what item 5 addresses. The list also keeps the number of layers from growing: once two coverings exist, the code calls for removal.

What changes in the 9th Edition

The 9th Edition (2026) takes effect December 31, 2026. Miami-Dade has said permit applications and plans submitted on or after that date must follow it, and online submissions after 4 PM on December 30, 2026 are held to the new edition. FRSA's February 2026 summary says approved changes to the recover section include:

  • Item 1 refers to "roof covering or roof system" components.
  • A new exception would allow an adequate existing or repaired substrate to stay when two coverings exist and the upper layers are removed. FRSA says this is aimed at reusing high R-value insulation or lightweight insulating concrete.
  • An existing vapor barrier or self-adhering membrane bonded to the deck could remain, with an added membrane permitted over it.
  • Asphalt shingle coating language moves to the shingle sections.

A June 2026 law-firm summary notes that these modifications remain pending until the code is finalized. Check the final text before relying on them.

Recover in Miami-Dade's HVHZ

The Existing Building volume points HVHZ buildings to sections 1512 through 1525. I did not find a clear plain-language statement of the HVHZ's layer limits in the sources I could read, so do not assume the non-HVHZ list above is the full HVHZ rule. What the sources do show:

  • Miami-Dade's roof inspection checklist lists moisture testing for roof recover under TAS 126 and uplift testing for recover under TAS 124.
  • A 2017 Palm Beach County advisory summarizing the HVHZ text says an existing assembly must not exceed 5 percent moisture by weight in the membrane and 8 percent in rigid board insulation, verified by a TAS 126 moisture survey, with results submitted with the permit application. That is an older, non-HVHZ county's summary, so confirm the current limits with Miami-Dade.
  • Roof assemblies approved for recover installations are listed on their Miami-Dade Notices of Acceptance by deck type. One earlier TPO approval I reviewed, for example, was written for recover decks only. See commercial flat roof systems.
  • The HVHZ 25 percent provision (section 1521.4) is described in Miami-Dade's summary of the 2023 changes. If a roof was built, repaired or replaced under the 2007 code or later and 25 percent or more is worked on, only that portion must meet the current code. See the 25% rule article.

For tile roofs in the HVHZ, ask the building department directly. Tile systems have their own approvals and attachment testing.

Questions people ask

Can I put new shingles over old shingles?

Outside the HVHZ, a recover over one existing layer may be allowed if no tear-off condition applies, and Collier County's summary says up to two layers total. In the HVHZ, ask Miami-Dade, since the HVHZ sections govern.

Can a metal roof go over existing shingles?

The code exception covers complete systems, such as standing-seam metal, that carry loads to the structure and do not depend on the existing roof. Whether a specific product may be installed this way depends on its approval and the local jurisdiction.

Do I need a permit for a recover?

A recover is a form of reroofing, so ask the building department what permit applies. See roof permit requirements in Miami-Dade.

Does a recover cost less?

It can reduce tear-off and disposal work, but I did not find a current, dated South Florida source for price differences. Compare written bids that spell out deck inspection, repairs and wet-material testing. See roof replacement cost estimates.

Check before you decide

  • Ask how many layers exist and what the deck and insulation condition is.
  • Ask whether moisture testing is planned for a low-slope recover.
  • Confirm which code edition applies to your permit, especially near December 31, 2026.
  • Ask for the product approval number and what deck types it covers.
  • Have a licensed roofing contractor put recover and tear-off options in writing.

Sources

  1. FRSA - When reroofing, the choice to recover or replace may not be yours (2022)
  2. FRSA - Changes in the 2026 9th Edition of the Florida Building Code (February 2026)
  3. Jimerson Birr - Florida Building Code tightens up: new wind resistance rules for roofing (June 2026)
  4. Collier County - Roof recover and replacement definitions (FBC 7th Edition, Existing Building)
  5. Miami-Dade County - Roof inspection checklist (recover testing references)
  6. Palm Beach County Building Code Advisory Board - Roof moisture surveys technical advisory (2017)
  7. Miami-Dade County - 2023 FBC roofing code changes (HVHZ)
  8. Miami-Dade County - Notice about the Ninth Edition Florida Building Code

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog