Skip to main content

Garage door wind ratings in Florida and the HVHZ

Why garage doors fail in hurricanes, what wind and impact ratings mean, how Miami-Dade approves and permits replacement doors, and what to check.

By AV Construction Group Corp. Published 7 min read

Illustration for articles about general contracting

A garage door is usually the largest opening in a house, and it is often one of the first parts to fail in a hurricane. When it does, wind enters the garage and pressurizes the house from inside. In Miami-Dade and Broward, a replacement garage door must be rated for wind pressure and debris impact, carry a current Miami-Dade Notice of Acceptance or equivalent approval, and be installed under a permit.

Why garage doors fail

A garage door is a wide span of thin panels held by tracks, rollers and brackets. The Building America Solution Center, a U.S. Department of Energy resource run by Pacific Northwest National Laboratory, describes three failure modes:

  • Suction: negative pressure on the downwind side pulls the door out of its tracks.
  • Inward push: positive pressure on the windward side buckles or pushes the door in.
  • Hardware failure: the track, brackets or other supports that hold the door give way.

A University of Florida extension publication from 2005 adds that a collapsed door lets wind in and creates internal pressure that can blow out windows, doors, walls and possibly the roof. The Florida Division of Emergency Management's Hurricane Retrofit Guide calls garage doors a common failure point that deserves early attention. Debris impact is a second risk, especially for doors with glass panels.

What a wind rating means

A wind rating is a design pressure, in pounds per square foot, that the door and its hardware were tested to resist, both pushing in and pulling out. Several standards come up:

  • ANSI/DASMA 108 and ASTM E330: pressure test methods accepted for residential codes. The Building America guide says ASTM E330 testing is done at 1.5 times the design pressure.
  • TAS 202: the Miami-Dade and Florida test protocol for static pressure. The same guide says it is required for garage doors in Florida's High-Velocity Hurricane Zone (HVHZ).
  • TAS 201 and TAS 203: large-missile impact and cyclic pressure tests used in the HVHZ.
  • ASTM E1886, ASTM E1996 and AAMA 506: impact test and specification standards that the same guide lists for impact-resistant doors.

Not every label tells you the rating. The Building America guide notes that many garage door labels omit wind or pressure ratings, and suggests checking the pressure test report in that case. A door needs a design pressure that matches the site, so ask the supplier for the rating, the wind speed it was designed for and the exposure category assumed. FEMA's Wind Retrofit Guide, second edition (2023), uses design pressures at least equal to a 130 mph wind in Exposure C, or the site's own higher speed, as its benchmark for garage doors. Miami-Dade's design wind speeds are higher: an Intertek presentation lists 175 mph for Risk Category II buildings under the code then in force. The county's approval and your plan reviewer decide what applies to a permitted door.

HVHZ approval and the NOA

Miami-Dade says products that make up the building envelope, including doors, need an approval before use in the county. The approval is the Notice of Acceptance (NOA). Broader background is in Florida product approval and the Miami-Dade NOA explained.

An example helps. A current NOA for a steel sectional garage door lists it as large- and small-missile impact resistant and cites TAS 201, 202 and 203. It does not state the pressure values; they sit in the approval drawing. It also says:

  • Each unit must carry a permanent label with the manufacturer, model, positive and negative design pressures, impact rating, installation drawing reference, NOA number and the statement "Miami-Dade County Product Control Approved."
  • The NOA has an expiration date and can end earlier if the product or its use changes.
  • The full NOA must be available at the job site when the building official asks.
  • The NOA cites the Florida Building Code, 8th Edition (2023).

Read the NOA for the exact door model, size range and installation method you are buying. Approvals are product specific, and a door installed outside its limits is not covered.

Code edition timing

Miami-Dade says applications on or after December 31, 2026, must follow the Ninth Edition (2026) Florida Building Code. If you are replacing a door near that date, ask your contractor which edition applies and whether the door's approval fits.

Permit and inspection

Miami-Dade's submittal checklist for overhead sectional doors asks for three items:

  1. An application with shop drawings, a process number and the total number of doors.
  2. Two copies of a plan showing the size and location of each door opening and the building's mean roof height.
  3. Two copies of the NOA for each door, which the professional of record must review. An HVHZ-level approval from the Florida Building Commission can be used in place of an NOA.

Cities in the county have their own building departments and forms, so check with yours. The checklist does not describe inspections. Ask which inspections your permit will have and whether the installer or you will schedule them. The permit process in general is covered in Miami-Dade building permit basics.

Options for an existing door

The Retrofit Guide and FEMA's public-facilities handbook describe several approaches. None is one-size-fits-all, and an engineer or the building department can say what is acceptable for your door and permit.

  • Replace the door. Replacement with a pressure- and debris-rated door is the approach both sources point to. The Retrofit Guide says replacements in Miami-Dade and Broward must meet this standard.
  • Add rated storm panels or shutters (see hurricane shutters vs impact glass) that are tested for both pressure and impact and installed in front of the door. Someone has to install them before each storm.
  • Use a manufacturer-approved retrofit kit. The Retrofit Guide says such kits may require new springs.
  • Add vertical bracing posts that have Florida Building Code approval. FEMA notes that a center post shortens the unbraced span, but the door cannot open while it is in place.

Two cautions come from the Retrofit Guide: horizontal wood bracing is generally ineffective and can make the door too heavy for the opener, and parking a car against the door gives little support. It also says only trained installers should adjust or replace springs, which hold a lot of stored energy.

Bracing and covers do not turn an old door into a tested one unless the product is approved for that use. Ask for the approval document, not just a sales description.

Maintenance and checks

The Retrofit Guide suggests checking garage doors for loose or missing brackets, bolts and hinge hardware, plus rust, rot and dents. FEMA's handbook recommends corrosion-resistant hardware within 3,000 feet of the coast, which covers much of South Florida. A wind-rated door still depends on its tracks, anchors and fasteners, so installation quality matters as much as the panel.

Questions people ask

Does my garage door need a permit to replace?

Miami-Dade's checklist treats overhead door installation as a permitted submittal with an NOA. Check with your building department for your exact case, because rules differ by city and change over time.

Is a door without windows exempt from the impact rating?

The Building America guide says glazed garage doors need impact protection in windborne-debris regions, and notes the glazing size that triggers it for retrofit options. In Miami-Dade and Broward, the Retrofit Guide says replacement doors must be pressure- and debris-rated. Ask your plan reviewer what applies to your door.

Can I use a Florida Product Approval instead of an NOA?

Outside the HVHZ, a Florida Product Approval is a common route. For a Miami-Dade permit, the county's checklist accepts an NOA or an HVHZ-level approval from the Florida Building Commission. Ask the building department which one your permit will accept.

Check before you decide

  • Get the NOA or approval number and read the model, size and installation limits.
  • Confirm the label will show positive and negative pressure ratings and impact rating.
  • Ask who pulls the permit and which inspections to expect.
  • Ask what happens to the opener, springs and tracks during replacement.
  • Keep the NOA, permit, inspection record and product label photo together.

See general contracting for related work on openings and envelope upgrades.

Sources

  1. Building America Solution Center (PNNL / U.S. DOE): Garage Doors Are Pressure Rated
  2. Florida Division of Emergency Management: Hurricane Retrofit Guide, Openings
  3. FEMA: Hurricane and Flood Mitigation Handbook for Public Facilities, Fact Sheet 3.2 (2022)
  4. FEMA: P-804 Wind Retrofit Guide for Residential Buildings, Second Edition (2023)
  5. University of Florida IFAS Extension: Decreasing Door Danger Zones (ABE378, 2005)
  6. Miami-Dade County: Overhead Sectional (Garage) Door Submittal Checklist
  7. Miami-Dade County: Notice of Acceptance 25-1218.05 (example, steel sectional garage door)
  8. Miami-Dade County: Construction Materials and Product Control Brochure
  9. Intertek / National Glass Association: Hurricane Standards, Testing and the Product Approval Process
  10. Miami-Dade County: Ninth Edition (2026) Florida Building Code Change Notice

Planning a project?

Tell AV Construction Group Corp. about your project and we will follow up.

Keep reading

More guides on the blog